Repair Bathroom Tile

Repair Bathroom Tile

Going from Old to New Instructions Step 1 Using a grout saw, scrape away as much grout around the tile as possible. Work slowly to avoid damaging the drywall or backing underneath. Creating this gap around the tile keeps the force of chisel blows on the broken tile from breaking the adjoining tiles. If your grout lines are 1/8 of an inch or narrower, check the adjoining tiles to make sure your grout saw won’t chip the tiles’ edges. If so, unscrew the blades and remove the saw-shaped insert for a narrower cut. Step 2 Place the tip of your chisel near the center of the tile and give it a light tap. Start gently and add force gradually. As bits of tile begin to break free from the center, find a spot where you can wedge the chisel between the tile and the wall. With moderate taps, loosen broken pieces of tile from the center. If some of the drywall paper pulls loose, don’t panic. Change the angle of your chisel to avoid making the damage worse and keep working. You’ll fill the damaged area with tile adhesive later on. Step 3 Once you establish your starting point at the center, use moderate taps to work your way toward the tile edges. If you’re removing a small tile, take advantage of the backing (which allows these tiles to be installed in sections) and wedge your chisel between the tile and its backing. Step 4 With all of the tile and adjoining grout removed, use a stiff-bladed putty knife to free any loose mastic still attached to the subsurface. It doesn’t need to be perfectly smooth, but it must be free of anything that would keep the replacement tile from resting flush with the others. Chip off any remaining grout around the opening. Finish by vacuuming dust from the opening. Step 5 Test-fit the replacement tile in the opening and check that its surface rests slightly below that of the surrounding tiles. You don’t need any fancy tools for this job; your fingertips will sense the differences in thickness. Apply an even 1/8-inch layer of tile adhesive or a combination adhesive/grout product on the back of the tile. (It’s called “buttering” the tile, even though it goes on more like creamed cheese.) Press the tile into position, centering it in the opening. CautionAvoid adhesives that aren’t specifically designed for tile. Tile adhesives spread and flatten as you push the tile against the wall or floor, supporting it evenly from underneath. They also help keep the tile from sliding out of place until the adhesive hardens. Step 6 Check the tile position immediately and confirm that it aligns with the surrounding tiles. Tape the replacement tile to the surrounding surface to hold it in position. Allow the adhesive to dry overnight or as recommended by the manufacturer. Step 7 Use a premixed grout/adhesive or mix grout to the consistency of peanut butter and use the tip of a plastic putty knife to press it into the grooves surrounding the tile. Also, fill any grout areas damaged during removal of the tile. Step 8 For a job this small, use your fingertip as a grout-smoothing tool to level it with the tile edges. Use a moist sponge to smooth the grout even with the tile edges and wipe away the excess. Avoid exposing the repair to moisture for several days as the grout hardens. Step 9 After about a week, apply grout sealer to the new grout to protect it from moisture. Allow a few extra hours to clean and seal the grout around the surrounding tile surfaces as well for long-lasting protection.
repair bathroom tile 1

Repair Bathroom Tile

Instructions Step 1 Using a grout saw, scrape away as much grout around the tile as possible. Work slowly to avoid damaging the drywall or backing underneath. Creating this gap around the tile keeps the force of chisel blows on the broken tile from breaking the adjoining tiles. If your grout lines are 1/8 of an inch or narrower, check the adjoining tiles to make sure your grout saw won’t chip the tiles’ edges. If so, unscrew the blades and remove the saw-shaped insert for a narrower cut. Step 2 Place the tip of your chisel near the center of the tile and give it a light tap. Start gently and add force gradually. As bits of tile begin to break free from the center, find a spot where you can wedge the chisel between the tile and the wall. With moderate taps, loosen broken pieces of tile from the center. If some of the drywall paper pulls loose, don’t panic. Change the angle of your chisel to avoid making the damage worse and keep working. You’ll fill the damaged area with tile adhesive later on. Step 3 Once you establish your starting point at the center, use moderate taps to work your way toward the tile edges. If you’re removing a small tile, take advantage of the backing (which allows these tiles to be installed in sections) and wedge your chisel between the tile and its backing. Step 4 With all of the tile and adjoining grout removed, use a stiff-bladed putty knife to free any loose mastic still attached to the subsurface. It doesn’t need to be perfectly smooth, but it must be free of anything that would keep the replacement tile from resting flush with the others. Chip off any remaining grout around the opening. Finish by vacuuming dust from the opening. Step 5 Test-fit the replacement tile in the opening and check that its surface rests slightly below that of the surrounding tiles. You don’t need any fancy tools for this job; your fingertips will sense the differences in thickness. Apply an even 1/8-inch layer of tile adhesive or a combination adhesive/grout product on the back of the tile. (It’s called “buttering” the tile, even though it goes on more like creamed cheese.) Press the tile into position, centering it in the opening. CautionAvoid adhesives that aren’t specifically designed for tile. Tile adhesives spread and flatten as you push the tile against the wall or floor, supporting it evenly from underneath. They also help keep the tile from sliding out of place until the adhesive hardens. Step 6 Check the tile position immediately and confirm that it aligns with the surrounding tiles. Tape the replacement tile to the surrounding surface to hold it in position. Allow the adhesive to dry overnight or as recommended by the manufacturer. Step 7 Use a premixed grout/adhesive or mix grout to the consistency of peanut butter and use the tip of a plastic putty knife to press it into the grooves surrounding the tile. Also, fill any grout areas damaged during removal of the tile. Step 8 For a job this small, use your fingertip as a grout-smoothing tool to level it with the tile edges. Use a moist sponge to smooth the grout even with the tile edges and wipe away the excess. Avoid exposing the repair to moisture for several days as the grout hardens. Step 9 After about a week, apply grout sealer to the new grout to protect it from moisture. Allow a few extra hours to clean and seal the grout around the surrounding tile surfaces as well for long-lasting protection.
repair bathroom tile 2

Repair Bathroom Tile

Step 1 Using a grout saw, scrape away as much grout around the tile as possible. Work slowly to avoid damaging the drywall or backing underneath. Creating this gap around the tile keeps the force of chisel blows on the broken tile from breaking the adjoining tiles. If your grout lines are 1/8 of an inch or narrower, check the adjoining tiles to make sure your grout saw won’t chip the tiles’ edges. If so, unscrew the blades and remove the saw-shaped insert for a narrower cut. Step 2 Place the tip of your chisel near the center of the tile and give it a light tap. Start gently and add force gradually. As bits of tile begin to break free from the center, find a spot where you can wedge the chisel between the tile and the wall. With moderate taps, loosen broken pieces of tile from the center. If some of the drywall paper pulls loose, don’t panic. Change the angle of your chisel to avoid making the damage worse and keep working. You’ll fill the damaged area with tile adhesive later on. Step 3 Once you establish your starting point at the center, use moderate taps to work your way toward the tile edges. If you’re removing a small tile, take advantage of the backing (which allows these tiles to be installed in sections) and wedge your chisel between the tile and its backing. Step 4 With all of the tile and adjoining grout removed, use a stiff-bladed putty knife to free any loose mastic still attached to the subsurface. It doesn’t need to be perfectly smooth, but it must be free of anything that would keep the replacement tile from resting flush with the others. Chip off any remaining grout around the opening. Finish by vacuuming dust from the opening. Step 5 Test-fit the replacement tile in the opening and check that its surface rests slightly below that of the surrounding tiles. You don’t need any fancy tools for this job; your fingertips will sense the differences in thickness. Apply an even 1/8-inch layer of tile adhesive or a combination adhesive/grout product on the back of the tile. (It’s called “buttering” the tile, even though it goes on more like creamed cheese.) Press the tile into position, centering it in the opening. CautionAvoid adhesives that aren’t specifically designed for tile. Tile adhesives spread and flatten as you push the tile against the wall or floor, supporting it evenly from underneath. They also help keep the tile from sliding out of place until the adhesive hardens. Step 6 Check the tile position immediately and confirm that it aligns with the surrounding tiles. Tape the replacement tile to the surrounding surface to hold it in position. Allow the adhesive to dry overnight or as recommended by the manufacturer. Step 7 Use a premixed grout/adhesive or mix grout to the consistency of peanut butter and use the tip of a plastic putty knife to press it into the grooves surrounding the tile. Also, fill any grout areas damaged during removal of the tile. Step 8 For a job this small, use your fingertip as a grout-smoothing tool to level it with the tile edges. Use a moist sponge to smooth the grout even with the tile edges and wipe away the excess. Avoid exposing the repair to moisture for several days as the grout hardens. Step 9 After about a week, apply grout sealer to the new grout to protect it from moisture. Allow a few extra hours to clean and seal the grout around the surrounding tile surfaces as well for long-lasting protection.

Repair Bathroom Tile

Repair Bathroom Tile
Repair Bathroom Tile
Repair Bathroom Tile
Repair Bathroom Tile

Leave a Reply

Your email address will not be published. Required fields are marked *